Bird watching is a delightful pastime that brings joy and a sense of connection with nature. Providing food for our feathered friends not only attracts a variety of beautiful birds to your backyard, but also supports them during harsh seasons when food is scarce. Crafting a homemade bird feeder is an affordable, eco-friendly, and engaging way to offer sustenance to these charming creatures. This article will guide you through several DIY bird feeder designs, suitable for all skill levels.
- Upcycled Soda Bottle Feeder Materials:
- 1 empty 2-liter plastic soda bottle, cleaned and label removed
- 2 wooden spoons
- Marker
- Utility knife or scissors
- String or twine
- Birdseed
Instructions:
- Using the marker, draw a small circle (approximately 1 inch in diameter) on one side of the soda bottle, about 3 inches from the bottom.
- Cut out the marked circle using a utility knife or scissors.
- Directly below the circle, draw a small horizontal line (about 1/4 inch) and cut it out as well. This will serve as the perch for the wooden spoon.
- Repeat steps 1-3 on the opposite side of the bottle.
- Insert the wooden spoons through the horizontal slots, ensuring they extend out on both sides of the bottle.
- Fill the bottle with birdseed.
- Tie a string around the neck of the bottle and hang it from a tree or hook.
- Pine Cone Feeder Materials:
- 1 large, dry pine cone
- Peanut butter (smooth or chunky)
- Birdseed
- Plate or shallow dish
- String or twine
- Butter knife or spatula
Instructions:
- Clean the pine cone by removing any debris, ensuring it is completely dry.
- Using the butter knife or spatula, cover the pine cone with a generous layer of peanut butter.
- Pour birdseed into the plate or shallow dish.
- Roll the peanut butter-coated pine cone in the birdseed, pressing gently to help the seeds adhere.
- Tie a string around the top of the pine cone, leaving enough length for hanging.
- Hang the pine cone feeder from a tree branch or hook.
- Orange Halves Feeder Materials:
- 2 oranges
- Knife
- Spoon
- 4 sturdy wooden skewers or sticks
- String or twine
- Birdseed
Instructions:
- Cut the oranges in half, then scoop out and remove the fruit from each half, leaving the peel intact.
- Carefully poke two holes opposite each other near the top edge of each orange peel.
- Insert a wooden skewer or stick through each pair of holes, forming a cross in the center of the orange peel.
- Fill each orange peel with birdseed.
- Thread a string through the skewers on each orange half, tying a knot to secure it.
- Hang the orange halves from a tree branch or hook.
- Tea Cup Feeder Materials:
- 1 teacup and saucer
- Waterproof adhesive (such as E6000)
- Birdseed
- String or twine
- A small twig or wooden spoon (optional)
Instructions:
- Ensure the teacup and saucer are clean and dry.
- Apply a generous amount of waterproof adhesive to the bottom of the teacup.
- Press the teacup firmly onto the saucer, positioning it off-center to create space for the birdseed.
- If using a twig or wooden spoon as a perch, apply adhesive to one end and attach it to the edge of the saucer near the teacup.
- Allow the adhesive to cure for at least 24 hours or according to the manufacturer’s instructions.
- Fill the teacup with birdseed.
- Tie a string around the handle of the teacup and hang it from a tree branch or hook.
- Tin Can Feeder
Materials:
- 1 empty tin can (such as a soup can), cleaned and label removed
- Acrylic paint and paintbrush (optional)
- Wooden dowel or sturdy twig (approximately 1/2 inch in diameter)
- Drill with a 1/2 inch bit
- Sandpaper
- Waterproof adhesive (such as E6000)
- String or twine
- Birdseed
Instructions:
- If desired, paint the exterior of the tin can with acrylic paint and allow it to dry.
- Using the drill, create a hole near the bottom of the can on one side, large enough for the wooden dowel or twig to fit snugly.
- On the opposite side of the can, drill another hole about 2 inches from the top for hanging.
- Sand any rough edges around the holes.
- Insert the dowel or twig through the lower hole, ensuring it extends out on both sides of the can to create a perch.
- Secure the dowel or twig with waterproof adhesive and allow it to cure according to the manufacturer’s instructions.
- Fill the tin can with birdseed.
- Thread a string through the top hole and tie a knot to secure it.
- Hang the tin can feeder from a tree branch or hook.
These five DIY bird feeder designs cater to various skill levels and preferences, ensuring that you can create the perfect feeder for your backyard. Regardless of which design you choose, remember to clean and refill your bird feeders regularly to maintain a safe and healthy environment for your feathered visitors. Happy birdwatching!